Ryobi c30 manual

Failure to follow all safety instructions listed below, can result in serious personal injury. Page 4: Specific Safety Rules Do not use any other cutting attachment. To install any other brand of cutting head to this string trimmer can result in serious personal injury.

Page 5: Symbols Some of the following symbols may be used on this tool. Please study them and learn their meaning for safe operation of this product. Page 6: Save These Instructions The following signal words and meanings are intended to explain the levels of risk associated with this product.

Page 7: Specifications If any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. Page Assembly Slightly rotate the cap from side to side until the button locks into place.

Install the front handle onto the top side of the drive shaft housing and move it to a comfortable position. Page 12 See Figure 8. The guard is shipped installed on these brushcutter models. Instructions have been included for reference when changing from string trimmer operation back to brushcutter operation. With the string head removed, place the brushcutter guard on the gear head as shown.

Page 13 2. Adjust the strap to a comfortable position. Page Operation To avoid burns from hot surfaces, never operate unit with the bottom of the engine above waist level. Hold the trimmer with the right hand on the rear handle and the left hand on the front handle. Keep a firm grip with both hands while in operation. The straight shaft trimmer cuts when passing the unit from left to right.

Brushcutter should be held at a comfortable position with the rear handle about hip height. Page Maintenance Failure to do so can cause poor performance, possible injury and may void your warranty. You can often make adjustments and repairs described here.

For other repairs, have the trimmer serviced by an authorized service dealer. Use only monofilament string. Use original manufacturer's replacement string for best performance. String Diameter: CS30 -. Stop the engine, disconnect the spark plug wire.

Hold the string head and unscrew the spool retainer. If you notice a power loss with your gas powered tool, you may need to remove these deposits to restore performance.

Drain all fuel from tank into a container approved for gasoline. Run engine until it stops. Clean all foreign material from the trimmer. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of these symptoms. It is presently unknown what, if any, vibrations or extent of exposure may contribute to the condition.

There are measures that can be taken by the operator to possibly reduce the effects of vibration:. When operating the unit wear gloves to keep the hands and wrists warm. Limittheamountofexposure per day. If you experience any of the symptoms of this condition, immediatelydiscontinueuseandseeyourphysicianabout these symptoms.

Wipe up any fuel spillage. Move 9 m 30 ft. Be sure the string head or blade is properly installed andsecurelyfastened. Failuretodosocancause serious injury. Do not use any other cutting attachment. To install any other brand of cutting head to this string trimmer can result in serious personal injury.

Keep string head below waist level. Never cut with the string head located over 76 cm 30 in. Maintain proper control until the blade has completely stopped rotating. Always make sure blade is installed correctly and securely fastened before each use.

Failure to do so can cause serious injury. Do not use any other blade. To install any other brand blade or cutting head to this brushcutter can result in serious personal injury. Do not use for any other purpose. Blade thrust is the reaction that may occur when the spinning blade contacts anything it cannot cut.

This reaction can be violent enough to cause the operator to lose control of the unit. Blade thrust can occur without warning if the blade snags, stalls, or binds.

This is more likely to occur in areas where it is difficult to see the material being cut. For cutting ease and safety, approach the weeds being cut from the right to the left.

In the event an unexpected object or woody stock is encountered, this could minimize the blade thrust reaction. Maintain a firm grip on both handles while cutting with a blade. Keep the blade away from body and below waist level. Some of the following symbols may be used on this tool. Please study them and learn their meaning for safe operation of this product. The following signal words and meanings are intended to explain the levels of risk associated with this product.

Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. When servicing, use only identical replacement parts. Toavoidseriouspersonalinjury,donotattempttooperate this product until you read thoroughly and understand completely the operator's manual. Save this operator's manualandreviewfrequentlyforcontinuingsafeoperation and instructing others who may use this product.

The operation of any product can result in foreign objects being thrown into your eyes, which can result in severe eye damage. Before beginning operation, always wear safety goggles or safety glasses with side shields and a full face shield when needed. We recommend WideVision Safety Mask for use over eyeglasses or standard safety glasses with side shields.

Engine displacement If any parts are missing, do not operate this tool until the missing parts are replaced. Failure to do so could result in possible serious personal injury. Welcome to ManualMachine. We have sent a verification link to to complete your registration. Log In Sign Up.