How to install multiple dish network receivers

DISH Using the azimuth and elevation angles, find a location for the satellite dish where it can be pointed towards the satellites located at these angles. Make sure nothing blocks the line of sight between the dish and the satellites.

Mount the mast to a solid surface so that the dish antenna cannot move or be bumped out of alignment. Never mount to a tree or a public utility pole.

Align the top part of the mast so that it is absolutely vertical. If the top part of the mast is off vertical by only a few degrees, it will be difficult or maybe even impossible for you to find the satellites. Take at least two readings with a level, on the upper mast, that are 90 degrees apart from one another.

Loosen both skew bolts and set the skew by rotating the dish mounting bracket to align the mark with the required angle on the skew scale which you wrote above. Tighten the skew bolts securely. See Table 1 for the required torque values. After the skew is set, do not try to finetune the skew angle when aiming the dish. Grounding, other devices, and in-home cabling must also meet these requirements.

RG-6 coaxial cable rated for at least to MHz must be used in this installation. Do not use existing cables such as RG as it may cause signal loss. Also, be sure that any outdoor connections are made using waterproof F-connectors rated for MHz or greater. The cable length between the DISH Damage caused by over-tightening is not covered by the limited warranty. Tighten all indoor coaxial cable connections to the receiver only by hand.

If you use a wrench, you may over-tighten the connections and damage your equipment. Connect a temporary cable to a peaking meter. Thread the other end of the cable through the LNBF arm and bracket. Attach the LNBFs to the bracket using the included screws. Can receive from 3 satellites, replaces earlier Dish which could only receive from 2. Local programming for selected markets were originally broadcast using the FSS Ku-band satellites.

Recently, Echostar has migrated many local markets to the new Currently, there remain a few selected local channel markets that require the use of a SuperDish to receive local channels. These markets will require a second dish if they wish to receive high definition programming. Appearance nearly the same as Just like the the is a legacy dish. The Dish Reception from , and and allowing 3 receivers.

Can also add a second dish. International programming from available. Install using a DPP 44 switch. Dish Network uses a general type of LNB called a circular feed lnb. ExpressVu and Dish Network are compatible. Remember, to receive from more than one satellite, more than one LNB was needed. Dish introduced a dual LNB system. The receiver needed a way to switch between one LNB and the other, depending on what satellite a particular channel resided on.

The Dish required a 2 in 1 out switch SW21 , and the 4 in 2 out SW42 switch for the receiver to receive from two satellites and Then Dish Network came up with the legacy Twin and the legacy Quad. The switching system had to be further improved to accommodate the connection of more than four total receivers. The old voltage switching control of the legacy LNB polarity became obsolete. With the new system the signal could be split to multiple receivers.

Coax cable which worked Ok for Legacy installations may not meet the needs of a DP installation. This is easier to separate signal with DP splitter. Twin and Quad legacy LNBs will connect up to four receivers. They have the SW21 for each output. The F simply refers to 'Feedhorn. We choose to use LNB since it is abbreviated. It cannot be split to support more than one receiver at a time.

It may be pointed to a single satellite in space. For the dual LNB version the multiswitched signal combines both satellites and to be carried on a single cable. Two cables may be connected to this unit for two receivers. The Legacy Twin points to two satellites in space. Legacy Quad: This unit has two circular LNB units inside one plastic housing, with four total receiver outputs. The multiswitched signal combines both satellites to be carried on one cable, and up to four receivers may be connected, one cable per receiver.

Powered splitter , can send the signal to two TVs simultaneously without signal degradation and one of the HDMI cords is 25' long. Top Selected Products and Reviews. To do this, simply split the signal using a multi-switch right after it passes the satellite dish and before it passes a receiver.

A multi-switch will allow up to four receivers and television sets that will operate independently of each other. Turn the connector on one end of the HDMI cable so the wider edge is on top and push the connector into the port on the back of the Dish Network receiver.

For a limited time, you get a Hopper Duo that allows you to record shows on 2 TVs. What's a Joey? Joeys allow customers to expand their service to multiple rooms in the house without having to add a separate DVR in every room.

Start watching a program in one room, pause it, and resume it in another room with a Joey. You'll need one Joey for each additional TV.

With its Whole-Home DVR network, Hopper makes it easier than ever to start watching a program in one room and resume in another.

Press the Pause button on your remote to pause the program. Go to the next room and pick up the DISH remote. Press the red button to display the TV Viewing Status screen. Next, connect one end of the HDMI cable to the 'output' port in the back of the satellite. Follow this guide to set up your replacement receiver. Unpack the new receiver. Unpack the contents of the box. Swap the old and new receivers. Connect receiver-to-wall wiring. Connect receiver-to-TV wiring. Connect the remote antenna.

Power on the receiver.